Turn on the device you want to program (TV, DVD, VCR or AUX)
Press the [Device] button (TV, DVD, VCR or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your brand
TV
VCR (use VCR key)
TV/VCR Combos (use VCR key)
DVD (use DVD key)
DVD Recorders (use DVD key)
TV/DVD Combos (use DVD key)
TV/DVD/VCR Combos (use DVD key)
DVD/VCR Combos (use DVD key)
Audio Device (use AUX key)
TiVo (use AUX key)
If the 3-digit code number you just entered is correct, the device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same [Device] button one more time
The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [CH▲] or [CH▼] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH▲] or [CH▼] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number Readback
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
The Learning Method
Press the [Device] button (AUX, TV, VCR or DVD) to be programmed and the [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
Line up the CLIKR-5 to the other remote, head-to-head, 1 or 2 inches apart
Press any button on the CLIKR-5 that you want to teach a command to. For example, if you want to teach the [MUTE] button, press the [MUTE] button
Press and hold the [MUTE] button on the other remote until the CLIKR-5Device LED light blinks twice The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating steps 3 and 4
Once you have completed teaching CLIKR-5 all desired commands for that Device, save the learned commands by pressing the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned correctly
Erasing a Single Learned Command
Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
Erasing All Learned Commands from One Device
Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold both the [Device] button you want to erase and the [PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
Programming a 5th Device to AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component
Turn on the equipment you wish to operate
Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [Device] button you want to setup. Point the remote control toward the Device and enter the 3-digit code number assigned to your brand
TV
VCR (use VCR key)
TV/VCR Combos (use VCR key)
DVD (use DVD key)
DVD Recorders (use DVD key)
TV/DVD Combos (use DVD key)
TV/DVD/VCR Combos (use DVD key)
DVD/VCR Combos (use DVD key)
Audio Device (use AUX key)
TiVo (use AUX key)
If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL : CBL TV : CBL VCR : CBL DVD : DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following steps
Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV TV : TV VCR : TV DVD : TV AUX : AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] button and [OK/SEL] simultaneously for three seconds
The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
Press the [VOL▲] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3
Macro Buttons
In the CABLE device mode, the [M1], [M2], and [HELP](see button functions below) can be programmed to act as a 'Favorite Channel' button.
This allows you to program up to 10 commands with one button press.
Press the [CBL] button to select the CBL mode
Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds
The [Macro] button will turn on for 30 seconds. The next step must be performed while the LED is on
Press up to 10 buttons you wish to store. The [CBL] Component LED will blink once for each command entered
Press the [CH▲] button to store the commands that were selected. The [CBL] button will blink twice to confirm the storage of commands
To erase the Macro programming and return to the original function:
Press the [CBL] button to select the CABLE mode
Press a [Macro] button and the [OK/SEL] button simultaneously for 3 seconds
The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is on
Press the [CH▲] button to erase the functions stored in the button. The CBL button will blink twice to confirm that the memory button has been erased
Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.