Skip to main content
Astound Broadband

CLIKR-5 (UR5U-6200)

 

Three-Digit Code Programming Method

UR5U-6200.jpg
  1. Turn on the device you want to program (TV, DVD or AUX)
     
  2. Press the [DEVICE] button (TV, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
     
  3. Point the remote control toward the device and enter the 3-digit code number assigned to your brand

    TV

    VCR (use VCR key) 

    TV/VCR (use VCR key) 

    DVD (use DVD key) 

    TV/DVD Combos (use DVD key) 

    TV/DVD/VCR Combos (use DVD key) 

    DVD/VCR Combos (use DVD key) 

    DVD Recorders (use DVD key) 

    Audio Device (use AUX key)

    TiVo (use AUX key) 
     

    • If the 3-digit code number you just entered is correct, the device will turn Off 
    • If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
       
  4. After you’ve entered the correct code number and the device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all work
     
  5. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
     
  6. Once you have found the correct 3-digit code, save it by pressing the same [DEVICE]  button one more time. The [DEVICE] LED light will blink twice to confirm that the code was successfully stored
 

Auto Search Method

UR5U-6200.jpg If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
 
  1. Turn on the equipment you wish to operate
     
  2. Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
     
    • The device LED will light on for 30 seconds. The next step must be entered while LED is on
       
  3. Press the [CH▲] or [CH▼] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH▲] or [CH▼] button as soon as the equipment turns off.
     
  4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
     
  5. Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
 

Code Number Readback

UR5U-6200.jpg
  1. Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds
     

    The device LED will light on for 30 seconds. The next step must be entered while LED is on
     

  2. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
     
    • Each digit is separated by 1 second. Ten blinks is equal to the number 0
    • For example, 108 will be:  One blink, [one second off], ten blinks, [one second off], eight blinks
 

Programming a 5th Device to AUX Button

UR5U-6200.jpg You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR, DVD or Audio Component

 

  1. Turn on the equipment you wish to operate. 

     

  2. Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
     
    • The device LED will light on for 20 seconds. The next step must be entered while LED is on
       
  3. Press the desired [DEVICE] button. Point the remote control toward the device and enter the 3-digit code number assigned to your brand

    TV

    VCR (use VCR key) 

    TV/VCR (use VCR key) 

    DVD (use DVD key) 

    TV/DVD Combos (use DVD key) 

    TV/DVD/VCR Combos (use DVD key) 

    DVD/VCR Combos (use DVD key) 

    DVD Recorders (use DVD key) 

    Audio Device (use AUX key)

    TiVo (use AUX key) 
     

  4. If the 3-digit code number you just entered is the correct number, the device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the device turns Off
     
  5. Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code
     
  6. Press [AUX] one more time. The desired [DEVICE] LED light will blink twice to confirm the code was stored
 

Programming the System On/Off Button

UR5U-6200.jpg The System on/off button can send out up to five power on/off commands for the devices you programmed into the remote control
 
  1. Press [CBL]
     
  2. Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
     
  3. Press [TV
     
  4. Press [DVD] (if adding)
     
  5. Press [VCR] (if adding)
     
  6. Press [AUX] (if adding)
     
  7. Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
 

Programming Channel Controls

UR5U-6200.jpg Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

 

CBL : CBL            TV : CBL            VCR : CBL         DVD : DVD             AUX : AUX 


If you wish to store the TV channel controls in TV mode, use the following steps
 

  1. Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
     
  2. Press the [VOL▲] button. The device LED will blink
     
  3. Press [TV] button. The device LED will blink twice to confirm the programming


    To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3
 

Volume Control

UR5U-6200.jpg Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

CBL : TV            TV : TV            DVD : TV            AUX : AUX 

 If you wish to store the Cable volume control in CBL mode, use the following steps
 

  1. Press [CBL] and [OK/SEL] simultaneously for three seconds
     
    •  [CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
       
  2. Press the [VOL▲] button. The device LED will blink
     
  3. Press [CBL] button. The device LED will blink twice to confirm the programming
     

To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3

 

Programming For Advanced Function (blank key)

UR5U-6200.jpg In the CBL mode, the M1, M2, Help, BLANK buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press
 
  1. Press the [CBL] button to select the CBL mode
     
  2. Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds
     
  3. Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
     
  4. Press the [CH▲] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions
 

Low Battery Warning

UR5U-6200.jpg When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
 

Memory Lock

UR5U-6200.jpg This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
 

Button Functions<

UR5U-6200.jpg UR5U-6200_buttons.jpg