Skip to main content
Astound Broadband

UF4-200C

 

Setting up Your Remote

UF4200C.jpg
  1. On the remote control, press and hold the appropriate mode key until the four mode keys flash twice. The mode key will continue to flash
     
  2. Enter the three-digit code



    • After you press the first digit, the mode key should light and stay on. After you press the last digit, the mode key should flash three times and turn off
       
    • If the mode key does not flash three times before turning off, the code is invalid for this device type. Repeat the procedure with another device code

       
  3. Point the remote at the device and press POWER. If the device turns on or off, you have finished programming
     
  4. If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScan™ section later in this manual
 

Setting up your Remote for an Auxiliary Device

UF4200C.jpg
  1. Press and hold AUX until the four mode keys flash twice. The AUX key will continue to flash
     
  2. Press and release the appropriate mode key for the device (VCR for a video cassette recorder, TV for a television, and CABLE for a cable device) until the four mode keys flash twice


    Look up the device manufacturer in the Television Codes, VCR codes sections, or Converter Codes sections and enter the three-digit code for your TV, VCR or Cable device




  3. After you press the first digit, the AUX key should light and stay on. After you press the last digit, the AUX key should flash three times and turn off
     
  4. If the AUX key does not flash three times before turning off, the code is invalid for this device type. Repeat the procedure with another device code
     
  5. Point the remote at the device and press POWER. If the device turns on or off, you have finished programming. If you have tried all the codes listed for the manufacturer and the device does not respond, refer to the CodeScan™ section later in this manual.
 

Codescan

UF4200C.jpg

If none of the codes listed for your Cable Box, TV, or VCR works, the CodeScan™ method will allow you to cycle through all the available codes in the remote until you find the right Cable Box, TV, or VCR code.

  1. Manually turn on power to the device for which you want to program the remote (TV, CABLE, AUX, VCR)
     
  2. Press and hold a mode key for approximately three seconds until the four mode keys flash twice. The selected mode key will continue to flash
     
  3. Press POWER. The mode key will stop flashing and remain on
     
  4. Point the remote control at the device
     
  5. Press and release the? key repeatedly and slowly. Each time you press the key, the remote sends the power-off command using a different device code
     
  6. When the device turns off, that means that the remote has been programmed with a code that can control the device. If you accidentally press the ? key after the device has turned off, press the ? key to return to the previous device code
     
  7. Test whether other functions operate using the remote control. If a primary function does not work, continue to press the ? key to find another code that turns off the device. Then test the functions again
     
  8. When you are satisfied that all primary functions are working, press OK to lock in the code
 

Recalling a Device Code

UF4200C.jpg

Perform the following steps to read the code currently set for a device. This is useful for retrieving a device code that was set using the CodeScan™ method.

  1. Press and hold a mode key until the four mode keys flash twice. The selected mode key will continue to flash
     
  2. Press HELP. The mode key flashes each of the three digits in the code
     
    • A pause separates each digit
       
    • For example, three flashes represent the number 3
       
    • Rapid flashing represents 0

       
  3. Count and record the sequence of flashes to determine the three-digit code
 

Programming Volume Control

UF4200C.jpg

By default, volume is controlled through your cable box; but if you have a TV that permits volume control, and you would to control volume through it, follow these steps (this procedure does not affect the device codes you set previously)

  1. Press and hold CABLE for approximately three seconds until the four mode keys flash twice. The CABLE key will continue to flash
     
  2. Press TV. The CABLE key will flash three times and turn off
     
  3. You now control the volume through the TV whenever you change the volume level in Cable mode

 

If you would like to return to volume control through the cable box, follow these steps:
 

  1. Press and hold CABLE for approximately three seconds until the four mode keys flash twice. The CABLE key will continue to flash
     
  2. Press CABLE. The CABLE key will flash three times and turn off
     
  3. You now control the volume through the TV whenever you change the volume level in Cable mode
 

Button Functions

UF4200C.jpg UF4200C_buttons.jpg
 

Installing/Replacing Batteries

UF4200C.jpg

Before you can program or operate the remote control, you must install two Alkaline AA batteries
 

  1. Remove the battery compartment cover on the back of your remote control
     
  2. Check battery polarity carefully, and install the batteries as shown in the illustration below
     
  3. Replace the battery compartment cover
     

IMPORTANT NOTE: Weak batteries may disrupt normal operation of the remote


UF4200B_battery_comp_small.gif