-
Programming Remote - Popular Brands
-
|
- Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
- Point the remote at the device and press and hold the [OK/SEL] and TV buttons together for 3 seconds While holding the device key (TV, AUD, DVD, AUX) the LED will light off and on again
- Begin to press the numbers keys, one at a time, starting with 1, then 2, 3, etc until the device turns off
# |
TV |
AUDIO |
DVD |
AUX |
0 |
SANYO |
ROTEL |
HITACHI |
BOSE |
1 |
SONY |
DENON |
SONY |
HP |
2 |
SAMSUNG |
YAMAHA |
PHILIPS |
APPLE / iPod |
3 |
LG |
MARANTZ |
SAMSUNG |
APPLE / iPod |
4 |
TOSHIBA |
SONY |
PHILIPS MAGNAVOX |
MICROSOFT / XBOX |
5 |
PANASONIC |
INTEGRA |
PANASONIC |
SONY / PS2 |
6 |
PHILIPS |
HARMAN KARDON |
LG |
LUTRON |
7 |
HITACHI |
PIONEER |
JVC |
X-10 |
8 |
SHARP |
ONKYO |
DENON |
X-10 |
9 |
VIZIO |
LEXICON |
PIONEER |
MICROSOFT / XBOX |
- If your brand does not appear in the brand chart, perform setup using either DIRECT CODE ENTRY or CODE SEARCH
- Press the device button (TV, DVD, AUX, or AUD) to save the code
- The device button LED will blink twice to confirm the code is stored
|
-
Three-Digit Code Programming Method
-
|
- Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
- Press and hold the device key (TV, AUD, DVD, AUX) and the [OK/SEL] button down together for 3 seconds until the device key stays lit
- The device key (TV, AUD, DVD, AUX) will stay lit for 30 seconds. The next step must be entered while the LED is on
- Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables
- Press [POWER] to turn the device back on
- If the device does not turn back on, repeat steps 1-5
- Press the device key (TV, AUD, DVD, AUX) again. The device LED will blink twice to confirm that the code has been stored
|
-
Auto Search Method
-
|
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
- Turn on the equipment you wish to operate
- Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on indicating that it's ready to be programmed
- Press [CH UP] or [CH DOWN] button and release. Do this every one second or keep the button pressed down. A new code will be entered one at a time Release the [CH UP] or [CH DOWN] button when the device turns off
- Press [POWER] to turn the device back on
- Try all of the functions of the remote control. If the buttons do not work as they should, repeat steps again
|
-
Code Number Readback
-
|
- Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on
- Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
- Each digit is separated by 1 second. Ten blinks is equal to the number 0
- For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
|
-
Volume Control
-
|
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
- CBL : CBL
- TV : TV
- DVD : TV
- AUD : AUD
- AUX : AUX
If you wish to store the TV volume control in CBL mode, use the following steps
- Press [CBL] and [OK/SEL] simultaneously for 3 seconds
- [CBL] will light on for 30 seconds. The next step must be entered while the LED is on
- Press [VOL UP]
- Press [TV]. [TV] will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [TV] with [CBL] in step 4
|
-
Battery Info
-
|
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment. |
-
Memory Lock
-
|
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control. |
-
Resetting The Remote
-
|
- Hold [CBL] and [REC] until the mode lights flash in order, should take roughly 5 seconds
- Reset does not cause the remote to lose its ability to control the converter
|
-
|