Skip to main content
Astound Broadband

UR4-DCT

 

Three-Digit Code Programming Method

UR4-DCT.jpg
  1. Turn on the equipment you wish to program. (TV, VCR, or DVD)
     
  2. Press  the [Device] button (AUX, VCR, or TV) and [OK] simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed
     
    •  The [Device] button will stay lit for 20 seconds. The next step must be entered while the LED is on
       
  3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered. 
    TV  

    VCR, TV/VCR*  (using VCR key) 

    DVD, TV/DVD* (using VCR key)  

    Auxiliary Device (using AUX key)  

    DMX & DCR (using AUX key) 

     
  4. Verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off
     
  5. Press the [Device] button again. The device LED will blink twice to confirm that the code has been stored

*To operate the volume control on TV/VCR & TV/DVD combination units, see Volume Control below
 

Auto Search Method

UR4-DCT.jpg If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
  1. Turn on the equipment you wish to operate
     
  2. Press the [Device] button and [OK] simultaneously for 3 seconds. The device LED will turn on
     
    • The device LED will light on for 20 seconds. The next step must be entered while LED is on
       
  3. Press the [CH▲] or [CH▼] button one step at a time or keep it pressed. The remote will emit a series of Power ON/OFF commands. Release the [CH▲] or [CH▼] button as soon as the equipment turns off.
     
  4. Verify that you selected the correct code by pressing [POWER] again. The equipment should either turn on or turn off
     
  5. Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
 

Code Number Readback

UR4-DCT.jpg
  1. Press the [Device] button and [OK] simultaneously for 3 seconds
     
  2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
     
  3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
     
    • Each digit is separated by 1 second. Ten blinks is equal to the number 0
    • For example, 108 will be:  One blink, [one second off], ten blinks, [one second off], eight blinks
 

Programming a Second TV to AUX Button

UR4-DCT.jpg
  1. Press [AUX] and [OK] simultaneously for 3 seconds. The device LED will turn on
     
    • The device LED will light on for 20 seconds. The next step must be entered while LED is on
       
  2. Press [TV] to pick up the TV code table
     
  3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered. 

    TV 
     
  4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored
 

Programming the System On/Off Button

UR4-DCT.jpg The System on/off button can send out up to three power on/off commands for the devices you programmed into the remote control
  1. Press [CBL]
     
  2. Press [System On/Off] and [OK] simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds
     
  3. Press [TV
     
  4. Press [VCR] (if adding)
     
  5. Press [AUX] (if adding)
     
  6. Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
 

Programming Channel Controls

UR4-DCT.jpg Channel controls (CH▲, CH▼, LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:  

CBL : CBL            TV : CBL            VCR : VCR            AUX : AUX 
If you wish to store the TV channel controls in TV mode, use the following steps.


1. Press the [OK] button and [TV] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on

2. Press the [VOL▲] button. The device LED will blink

3. Press [TV] button. The device LED will blink twice to confirm the programming


To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

 

Volume Control

UR4-DCT.jpg Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

CBL : TV            TV : TV            VCR : TV            AUX : AUX 
 If you wish to store the Cable volume control in CBL mode, use the following steps
 

  1. Press the [OK] button and [CBL] button simultaneously for three seconds
     
    • The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
       
  2. Press the [VOL▲] button. The device LED will blink
     
  3. Press [CBL] button. The device LED will blink twice to confirm the programming
     
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3.     To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps 
  1. Press the [CBL] button and the [OK] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
     
  2. Press the [VOL▲] button
     
  3. Press the [VCR] button. The device LED will blink twice to confirm the programming
 

Low Battery Warning

UR4-DCT.jpg When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.
 

Memory Lock

UR4-DCT.jpg This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
 

Button Functions

UR4-DCT.jpg UR4-DCT_buttons.jpg