Skip to main content
Astound Broadband

UR3-SR3

 

Manual Programming

UR3-SR3.jpg The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of equipment
 
  1. Turn on the equipment that you want the remote control to operate (Cable Box, TV, VCR, or DVD)
     
  2. Press the [Device] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 20 seconds. The next step must be entered while the LED is on
     
  3. Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off
     
    Cable Converter- [CBL] key
    TV - [TV] key
    VCR - [VCR] key
    TV/VCR combo* - [VCR] key
    DVD - [VCR] key
    TV/DVD combo* - [VCR] key

     

    • You can verify that you have selected the correct code by pressing the [MUTE] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e. VOL▲, VOL▼, CH▲, CH▼, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 using the next three digit code number from the brand list
       
  4. Store the three-digit code by pressing the same [Device] button once again. The device LED will blink twice to confirm that the code has been stored.
     

*To operate the volume control on TV/VCR & TV/DVD combination units, see Volume Control below

 

Auto Search Method

UR3-SR3.jpg If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:

 

  1. Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
     
  2. Press the [Device] button and [SELECT] simultaneously for three seconds
     

    The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is on
     

  3. Press [CH▲] or [CH▼] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release [CH▲] or [CH▼] as soon as the equipment turns off
     

    You can verify that you have selected the correct code by pressing [MUTE]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the Auto Search Method
     

  4. Press the same [Device] button to store the code. The device LED will blink twice to confirm that the code has been stored.
 

Code Number Readback

UR3-SR3.jpg This is useful for determining a device code that was set using the Auto Search Method above
 
  1. Press the [Device] button and [SELECT] simultaneously for 3 seconds
     
  2. The device LED will light on for 20 seconds. The next step must be entered while LED is on
     
  3. Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
     
    • Each digit is separated by 1 second. Ten blinks is equal to the number 0
    • For example, 108 will be:  One blink, [one second off], ten blinks, [one second off], eight blinks
 

Programming a Second TV to DVD key

UR3-SR3.jpg
  1. Press [VCR] and [SELECT] simultaneously for 3 seconds. 
     
    • The device LED will light on for 30 seconds. The next step must be entered while LED is on
       
  2. Press [TV]
     
  3. Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered. 

    TV 
     

  4. Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored
 

Programming the 'All Off' Button

UR3-SR3.jpg This allows you to program the [All OFF] button so it can send up to three power On/Off commands with one button press
 
  1. Press [CBL]
     
  2. Press [All OFF] and [SELECT] simultaneously for 3 seconds. The [CBL] button will turn on for 30 seconds
     
  3. Press the first [Device] button you want to store and then the [POWER] button
     
  4. Press the second [Device] button you want to store and then the [POWER] button
     
  5. Press the third [Device] button you want to store and then the [POWER] button
     
  6. Press [CH▲] to save the power commands you stored. The [CBL] button will blink twice to confirm
 

Volume Control

UR3-SR3.jpg Volume and Mute control are factory programmed to the respective Device mode you select, as follows:

CBL : TV            TV : TV                  DVD : TV

 If you wish to store the Cable volume control in CBL mode, use the following steps

 

  1. Press the [SELECT] button and [CBL] button simultaneously for three seconds. 


    The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
     
  2. Press the [VOL▲] button. The device LED will blink
     
  3. Press [CBL] button. The device LED will blink twice to confirm the programming
     

To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [CBL] with [TV] in Step 3.

 

 

To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps 

  1. Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
     
  2. Press the [VOL▲] button
     
  3. Press the [VCR] button. The CBL device LED will blink twice to confirm the programming
 

Programming Channel Control

UR3-SR3.jpg Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:

 

CBL : CBL          TV : CBL            DVD : DVD


If you wish to store the TV channel controls in TV mode, use the following steps.


1. Press the [SELECT] button and [TV] button simultaneously for three seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is on

2. Press the [VOL▲] button. The device LED will blink

3. Press [TV] button. The device LED will blink twice to confirm the programming


To return TV device to CBL channel repeat steps above replacing [TV] with [CBL] in Step 3

 

Low Battery Warning

UR3-SR3.jpg When the battery is low, the remote control LED blinks 2 times whenever a [Device] button is pressed to turn on equipment.
 

Memory Lock

UR3-SR3.jpg This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
 

Button Functions

UR3-SR3.jpg UR3-SR3_buttons.jpg