The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Turn on the device
Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD, TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key
If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
If the device you’re are attempting to program does not match the selected key (e.g. a second VCR = AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix code
Prefix:
Device:
0
Television
1
DVD Player, VCR, or PVR
4
Audio Device
5
Combo Units
Press and release the POWER key. The device key will stop flashing and remain on
Point the remote control at the selected device
Press and hold the ▲ key until the device turns off. While holding the ▲ key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the ▼ key to return to the previous code
When the device turns off, you have found a candidate code. Press the POWER Key to turn device back on. Test various functions using the remote control to determine if this code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the ? key to find another device code
Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall and record your device codes. When all the codes have been attempted the device button will flash rapidly
Manual Programming
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using Automatic Programming above
Recalling a Device Code
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using Automatic Programming above
Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to flash
Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents 0. A code of 1032 will be shown as:
Count and record the sequence of flashes to determine the four-digit code.
Programming Volume Control
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
Press and release the VOLUME ▲ key, the CBL key will remain on
Press and release the VOLUME ▼ key. The CBL key will turn off when VOLUME ▼ is pressed, and will turn on when released
Press and release the key corresponding to the device you wish to use to control volume (TV or AUD). After you release the key, the CBL key will flash three times and turn off
To return volume control to the default state:
Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
Press and release the VOLUME ▲ key. The CBL device key will stop flashing and stay on
Press and release the VOLUME ▼ key, and then press and release the OK key
After you release the OK key, the CBL device key will flash three times and turn off
Master Power Control
The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the POWER button. The following steps describe how to program the Master Power Control function:
Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to flash
Press and release the POWER key
Individually press and release each device key corresponding to the components you wish to be controlled by Master Power (starting with the cable device key).
NOTE: If no keys are pressed in this step, no change will occur
Press and release the POWER key. The CBL key will flash three times and turn off
Manually turn on all devices. Then test the Master Power control by pressing the POWER key
To disable Master Power, repeat the previous steps selecting only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER key in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master Power selection, press the DEVICE key for that device and immediately press the POWER key.
Channel Lock
Channel Lock causes channel up and down functions to always operate the settop box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected. The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate Channel Lock:
Press and hold the CBL device key until all the device keys begin to flash (approximately 3 seconds). Release the CBL key. The CBL key will
continue to flash
Press and release the CHANNEL ▲ key
Press and release the CHANNEL ▼ key
Press the OK key. The CBL device key will flash three times to confirm
